The
LOM II is the lead trimming machine that started it all and
has thousands of satisfied customers!
Two types of Fixturing... Both the Universal Vacuum and the
Production Vacuum Fixturing systems draw the board flat, removing
all
warp and allow trimming as close as .015 Inch (.38 mm).
Both systems use precision standoffs for supporting the board
under
vacuum. The Q Vacuum Source is designed to allow quiet, continuous
operation with minimum air flow. It produces about 80 inches
(203 cm) of water which will temporarily flatten even the
most severely warped boards. The Vacuum Source Canister provides
convenient storage for up to 10 gallons (37.8 liters) of scrap
lead material trimmed from boards.
When you purchase an LOM II, it is complete! You will be
ready to start trimming immediately. All tools and accessories;
micro-adjust tool, Quiet-Vac vacuum source, building blocks,
2 expandable V-Blocks, precision standoffs, cutter change
tool, motor lock tool, production vacuum fixture kit, set
of Allen Wrenches and owner's manual are included.
The LOM II comes to you complete! You will
be ready to start trimming immediately.
Safety is an important issue to consider
when purchasing a lead trimmer and Q Corporation addresses
this issue.
1) Key operated master switch.
2) Operator must depress two buttons in unison to start cutter.
3) Dynamic braking - 1 second to full stop
4) Safety shielding
Production
Vacuum Fixturing is the fastest, most accurate fixturing
system. It will accommodate any size or shape board within
an area of 13.5 by 14.25 inches (34.3 x 36.2 cm). Multiple
smaller boards can be fixtured to improve efficiency. Production
Vacuum Fixtures are committed to the boards for which they
are tooled. They can be interchanged on the LOM II in about
30 seconds.
Universal
Vacuum Fixturing is an adjustable system to allow fixturing
rectangular boards up to 13.5 by 14.25 inches (34.3 x 36.2
cm). Set-up time to change board sizes is approximately two
minutes. A channel in the baseplate side of the fixturing
allows using a blank board for faster, more accurate fixture
set-up. Vacuum support standoffs can be permanently attached
to this board to further reduce set-up time.
Lead-O-Matic II Specifications
Speed
Trims 2000 to 3000 leads per minute
Board Size
Up to 13.5" x 14.25" (34.3 x 36.2 cm) with universal
vacuum fixturing
Larger boards can be accommodated on production vacuum
fixture
Cutter Height
Continuously adjustable
Recommended Cut Height
.025" to .060" (.64 to 1.5 mm)
Max. Component Height
2" (5.1 cm) with standard fixturing
Cutter Size
3" diameter standard
Safety
Two handed operation, keylock power switch, dynamic
braking and safety shielding are employed. The LOM 11
has been accepted by countless safety engineers and
reviewed without comment by many Occupational Safety
and Health Authority representatives.
The
LOM II is the lead trimming machine that started it all and
has thousands of satisfied customers!
Production
Vacuum Fixturing is the fastest, most accurate fixturing
system. It will accommodate any size or shape board within
an area of 13.5 by 14.25 inches (34.3 x 36.2 cm). Multiple
smaller boards can be fixtured to improve efficiency. Production
Vacuum Fixtures are committed to the boards for which they
are tooled. They can be interchanged on the LOM II in about
30 seconds.
Universal
Vacuum Fixturing is an adjustable system to allow fixturing
rectangular boards up to 13.5 by 14.25 inches (34.3 x 36.2
cm). Set-up time to change board sizes is approximately two
minutes. A channel in the baseplate side of the fixturing
allows using a blank board for faster, more accurate fixture
set-up. Vacuum support standoffs can be permanently attached
to this board to further reduce set-up time.